NC Machinery Logo

336 Excavator

  • Specs Summary

Cat C18 Auxiliary/Generator Set Engine (EPA Tier 3)

C18 ACERT auxiliary/generator set engines incorporate a separate circuit aftercooling system (SCAC) for all configurations. The primary advantage of the SCAC systsem is reduced aftercooler corrosion since no sea water circulates through the aftercooler. Many other improvements on these engines also contribute to minimizing owning and operating costs. The EPA Tier 3, IMO II, EU Stage IIIA compliant ratings are available with heat exchanger or keel cooled options. All major MCS type approvals are available from the factory.

Standard Equipment

AIR INLET SYSTEM

  • Separate circuit after-cooled (SCAC)
  • Open Crankcase Ventilation (OCV) system
  • Turbocharger, jacket water cooled
  • Turbocharger inlet, 152 mm (6 in) OD straight connection
  • Air Inlet Adapter

CONTROL SYSTEM

  • Programmable low idle
  • Electronic diagnostics and fault logging
  • Electronic fuel/air ratio control
  • Engine Protection Mode for extended ambient conditions - EPA Tier 3 Ratings Only
  • 70-pin customer connector
  • Three types of throttle inputs (primary/ secondary PWM, 0-5V, 4-20mA
  • MECP I - Marine Engine Control Panel
  • Caterpillar Alarm and Protection
  • Load Sharing Attachment

COOLING SYSTEM

  • Separate Circuit After-Cooling (SCAC) for both HEX and Keel cooled engines
  • Engine JW and SCAC Shell & Tube Heat Exchangers for HEX cooled engines
  • SCAC pump, gear driven, for HEX cooled engines only
  • Jacket water pump, gear driven
  • Auxiliary water pump, gear driven
  • Sea water pump, bronze impeller, gear driven
  • SCAC and JW shunt tanks for maintaining proper pump inlet pressures
  • Aux Expansion Flange Kit

EXHAUST SYSTEM

  • Dry Elbows
  • Water-Cooled Elbows
  • Flexible Fitting
  • Flange
  • Muffler
  • Muffler Spark Arresting
  • 152 mm (6 in) round flanged outlet
  • Water-cooled exhaust manifold & turbocharger

FLYWHEELS & FLYWHEEL HOUSINGS

  • Flywheel Housing, SAE No. 0
  • Flywheel, 18 inch, 136 teeth
  • SAE standard rotation

LUBE SYSTEM

  • Front service simplex oil system
  • Center sump oil pan:
  • Duplex Oil Filters
  • Front and top service oil filler locations
  • Sump Pump
  • Front service dipstick
  • Oil pump, gear driven

POWER TAKE-OFFS

  • Crankshaft Pulleys
  • Front Stub Shaft
  • Hydraulic Pump Drive Adapter
  • Hydraulic Pump Drive
  • Front Enclosed Clutch
  • Crankshaft Pulleys
  • Front Stub Shaft
  • Front Enclosed Clutch

GENERAL

  • Front damper guard
  • Front service engine
  • Common electrical bonding point
  • Engine does not ship with zinc components
  • NOTE: These engines are for constant speed generator set applications only, and NOT to be used for variable speed applications

Optional Equipment

CHARGING SYSTEM

  • Battery Chargers
  • Charging Alternators
  • Alternator Mounting Group
  • Ammeter

FUEL SYSTEM

  • Duplex Fuel Filters
  • Fuel Cooler
  • Primary Fuel Filters
  • Flexible Fuel Lines
  • Front service simplex fuel system
  • Fuel transfer pump, gear driven
  • Manual fuel priming pump
  • Hybrid fuel line design

INSTRUMENTATION

  • Instrument Panels
  • OEM Wiring Harness
  • Gauges
  • Oil Level Sensor

PROTECTION SYSTEM

  • Marine Classification Society and SOLAS

STARTING SYSTEM

  • Electric Starting Motors - Single 24 Volt
  • Air Starting Motor
  • Air Start Accessories
  • Starting Aids - JW Heaters
  • Battery Sets - 24 Volt - Dry

MOUNTING SYSTEM

  • Front support - adjustable
  • Front Support
  • REAR ENGINE SUPPORT

PACKING

  • Engine Protective Cover
  • Storage Preservation
  • Export Packing